Potrei cambiare il modo di rappresentare i dati, ma questa è una modalità comune per riportare in una relazione di calcolo i risultati delle verifiche di sicurezza strutturale. L’immagine rappresenta l’elemento strutturale per il quale sono state prodotte le verifiche, riportate numericamente, per i diversi punti, nella tabella sottostante.
Riporto il sorgente per chiarezza (i numeri della tabella sono puramente indicativi):
\begin{figure}[p]
\centering
\includegraphics[width=0.44\columnwidth,angle=90,trim=5.3cm 1.8cm 4.0cm 1.8cm,clip]{1X=0}
\caption{Parete direzione Y a quota X=0}
\vspace{1cm}
\resizebox{0.75\columnwidth}{!}{
\begin{tabular}{ccrrrrrrrrrrrr}
\toprule
& & \multicolumn{3}{c}{\textbf{FSE(+X+0,3Y)}} & \multicolumn{3}{c}{\textbf{FSE(-X-0,3Y)}} & \multicolumn{3}{c}{\textbf{FSE(+0,3X-Y)}} & \multicolumn{3}{c}{\textbf{FSE(-0,3X+Y)}} \\
\cmidrule(lr){3-14}
\textbf{Section} & \textbf{Allineamento} & \multicolumn{12}{c}{\textbf{Coefficienti di sicurezza}} \\
\textbf{Cut} & \textbf{y[m]} & \textbf{N} & \textbf{M} & \textbf{T} & \textbf{N} & \textbf{M} & \textbf{T} & \textbf{N} & \textbf{M} & \textbf{T} & \textbf{N} & \textbf{M} & \textbf{T} \\
\midrule
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
1 & 2 & 3 & 4 & 5 & 6 & 7 & 8 & 9 & 10 & 11 & 12 & 13 & 14 \\
ecc…
ecc…
ecc…
ecc…
\bottomrule
\end{tabular}}
\captionof{table}{Coefficienti di sicurezza: Parete direzione Y a quota X=0}
\end{figure}
La tabella è molto larga, ma riesco a restringerla con il comando \resizebox.
Purtroppo però è anchè lunga e, come detto, vorrei poterla scrivere subito dopo la figura, eventualmente su più pagine successive.
Grazie,
Fabrizio